Shower Leaks Behind the Wall: How Your Plumber Fix Them In 7 Steps | Denton, TX

Shower Leaks Behind the Wall: How Your Plumber Fix Them In 7 Steps | Denton, TX

Photo By Julie Bowman at Shutterstock

Shower leaks behind walls happen for several reasons and can lead to expensive water damage. Luckily, they’re easy to prevent and even easier to fix with a little help from your friendly and trustworthy local plumber in Denton, TX.

Here’s how you do it:

Step 1 – Inspection

Your shower leak may be caused by any one of several problems, such as rotted wood or misaligned screws, so an experienced eye must take a look around before moving forward. If there is visible structural damage present within the walls, call your plumber immediately.

When you’re inspecting the shower itself, take note of worn caulking and cracked tiles that may be allowing water out.

Step 2 – Prep Work

As with any home repair, prep work is essential for your safety and the safety of the plumber you’ll be calling on. Ensure that all exposed pipes and wires have been covered adequately before starting repairs, so no one gets hurt while things are open to the air. It’s also wise to turn off power to your shower at the breaker box if possible.

Step 3 – Replacing Wood

If there is rotted wood involved in your problem or any exposed screws causing misaligned tiles, this step will need to be taken care of first. Carefully remove any pieces of rotted wood and replace them with new ones cut from scraps or a new sheet of wood. Nail or screw the new pieces into place and then caulk between them for a nice, clean finish.

Step 4 – Replacing Caulking

If you have old caulking that has seen better days, applying a new bead is simple but must be done properly with all materials being damp-free. Take care to match the color as closely as possible to prevent unsightly lines after it dries. When your sealant is applied correctly, allow it to dry before continuing onto step 5.

Step 5 – Replacing Tiles

Finally, time to take down those tiles! You’ll want to be careful here not to break any of them, so make sure your work area is clear and give them a firm tug towards you. Once all loose tiles are removed, apply caulking around the area where they meet the wall and place new ones. Keep them all aligned for an even finish.

Step 6 – Bolts & Screws

If screws or bolts protrude through your tile work, use special caps to cover them up to prevent injury. You must allow time for these caps to cure before getting water on them again, so leave this step until there is absolutely no chance of rain hitting your home anytime soon.

Step 7 – Finishing Touches

Replace all lock nuts, handle sets, and other fittings in their proper places before turning your power back on and testing your new seal. If all goes well, you would be able to enjoy a leak-free shower from now on!

Tips to Prevent Shower Leaks

  • Keep your shower well-maintained. Keep caulking around the base of your wall tiles fresh and clean, replace any cracked or broken tiles as soon as you can, and make sure all screws are firmly set in place.


  • Keep an eye out for changes in your home that may require repairs. Are tiled walls curling away from the bathroom floor? Are water spots forming on ceilings near showers? If you see signs like these, call a plumber in Denton, TX, to come to do a safety check right away!


  • Watch for signs of leaks. If you think your shower may be leaking, look out for puddles or water damage in hard-to-reach places like near ceilings or behind closed cupboards.


  • Keep it level! Ensure that all of your tiles are securely in place before getting into the shower, and turn off the water if you see any loose tiles. If they seem to move under hand pressure when trying to remove them, leave it up to a professional plumber who knows what they’re doing instead of risking injury.


  • Clean up after yourself! Accidents happen, so don’t forget to wipe down surfaces when done showering and clean up any mold on grout lines with a mix of bleach and water before scrubbing with a toothbrush. This will eventually prevent the need for a full-on grout replacement.

Why Is It Best to Call a Professional Plumber to Repair Shower Leaks?

When it comes to water damage and flooded bathrooms, the last thing you want is a DIY job done poorly. A leak is bad enough, but if your shower hasn’t been properly sealed from the beginning, using a plumber will just result in more problems down the line.

It’s also important to note that cleaning supply stores sell “instant fix” solutions that are only designed for temporary use with mirrors or countertops that aren’t directly affected by water. Your shower needs special attention due to how much moisture baths tend to create, so rely on real professionals who know what they’re doing instead of trying something at home that could end up causing more harm than good.

Don’t let leaks go untreated for too long. Always remember to clean up after yourself in the bathroom, inspect your home for any signs of water damage, and let a professional do their job if you suspect problems. This will save you time in repairs down the road!

Trust a Local Plumber in Denton, TX, for Shower Leaks

With our 24/7 emergency response and quick turnaround times, we’re the go-to company for homeowners who need fast solutions.

Whether you have a leak or clogged drain that’s causing water damage to your home, contact us right away to get an expert plumber out to your place immediately.

We provide same-day service seven days a week, so don’t hesitate about calling bluefrog Plumbing + Drain of North Dallas if you see any signs of trouble with your shower. Contact our expert plumbers right away.

Plumber Highland Park, TX

Call Now For
Emergency Service!


bfpad Proactive Protection ProgramTM

Many of our customers are so happy with our service that they become a bfpad Proactive Protection Program™! Contact us to learn more.

  • Priority Service
  • Free Annual Plumbing Evaluation
  • 15% OFF Service